7 Ways to train a dog to sit still and obey the owner’s command

Training a dog to listen to your commands is always the desire of the owners. In the article below, Petlandlover will suggest you 7 ways to train a dog to sit still on the owner’s command.

Table of Contents

1. Teach your dog to lie down and sit – Train a dog

Step 1: Command to sit

You stand close to the dog at a distance of 1m, then command the dog to “Sit” in front of you. In your left hand, hold the rope up high so that the dog’s neck is slightly raised. The right hand is facing the dog so that the dog can clearly see the movement of calling “Sit”. You need to note that the command must match the hand raised high at the same time.

Step 2: Give the command to lie down

After completing the “Sit” movement for the dog, continue to shout the “Lie” command. and ordered to bend down. Use your right hand to pull the rope face down into your palm and lower it close to the ground. You continue to repeat so that the dog “Lies”, “Sits” like that about 20 – 30 times.

Step 3: Extend the distance

In the following practices, you gradually increase the distance until the entire length of the rope is 10-25m. Once your dog has mastered it, you can remove the leash and train using hand commands.

Step 4: End the command

You stand about 10 meters away from the dog, then shout “Sit” and raise your right hand high. Your palms are extended forward, the tips of your hands pointing to the sky. When you call the dog “Lie”, you simultaneously lower your arms to your hips, palms facing the ground.

Ideally, you should do this exercise for your dog 3 times a week so that the dog can gradually absorb such simple commands. To encourage your dog to perform better, you can use treats.

2. Train your dog to sit still

Step 1: Command Sit

You call until he comes close and then command “Sit”. Wait about 3.4 seconds, then press the Clicker (training bar for dogs) and reward it.

Step 2: Order Yen

You repeat the above action but this time prolong the waiting time for the dog, so that the dog patiently waits for the reward. You also don’t have to give your dog a reward immediately after doing it right. Once you’ve practiced a few times and your dog is more used to waiting for a long time, you can start using the “Yet” command.

Step 3: Command to sit still

When the dog begins to understand and listen to the “Yet” command, it must sit and wait. You combine the command with the Sit command. Specifically, you will shout “Sit still” and the dog will maintain its sitting position. Then, you gradually lengthen the distance you stand near the dog.

Every time you give the command “Sit still”, you take a step back. If you see your dog still sitting still, press the Clicker and reward it with food.

Step 4: Repeat many times

You repeat the above action and each time lengthen the distance with the dog a little. If you see the dog still sitting still, press the Clicker and step closer to the treat.

If the dog moves without your permission, immediately come and pull the dog back to its original position and old position, then start practicing again.

3. Teach your dog to sit quietly and wait for the correct lesson

How to teach your dog to understand the wait command

First, you need to use language and actions to inform your dog that he must “Wait”. Then, leave and turn around to see if the dog is still as still as when you left. If the dog still stands still in the original position, you can return to reward him by giving him food and stroking his neck and shoulders.

Pay attention when teaching your dog to sit and wait
You need to have patience if you want to train your dog to sit still. Sometimes they may not listen because they don’t understand what you want. At that time, you should guide them from the beginning.

4. Teach your dog to sit obediently with both legs in place

Method 1

You put the dog in a sitting position facing you, so that the distance between you and the dog is just enough so that when the dog stands up, it will not get entangled with you.

You hold the food close to your dog’s nose so he can sniff it and follow it. You slowly raise your hand up, slightly angled above the top of your head so that it has to raise its head. In that position, the dog is required to lift its legs off the ground.

As soon as the dog lifts its legs off the ground, press the Clicker and reward with food immediately.

You repeat that action, each time raising the food higher and then pressing the Clicker so the dog understands that it must lift its paw higher. When your dog gets more used to it, you can use the command “Sit high” or “Hello” right before pressing the Clicker and rewarding it with food.

Method 2

You put the dog next to you, level with your left knee. Use your left hand to gently pull the reins on the dog’s neck upwards and push the dog’s tail straight back.

You let the dog sit firmly, so that the dog’s buttocks and tail form a stirrup position. At first, use your left knee as a fulcrum for your dog to lean on. Once the dog is sitting firmly, slowly pull your knee out and let the dog sit on its own.

Method 3

Similar to method 1, but this time, use your left hand to hold the dog’s collar, not pull up the reins. Next, slide your right hand under the dog’s chest or use a small stick to slide under the dog’s belly to gradually lift the dog’s body up. You place your dog’s front legs and your arms on the stick.

Once the dog has maintained a balanced position, slowly pull out your arm (or stick) and let the dog continue to sit in that position. Once your dog can sit steadily without any assistance, you can move on to practicing remote control.

5. Teach your dog to sit with food

Step 1

You stand in front of the dog, then hold the hand holding the food right above its nose. You move that hand to the top of your head and place it between your ears. By reflex, the dog will raise its head to look at the food and place its butt on the ground. Right then, press Clicker and reward it with food.

Step 2

You move to another place so the dog can stand up, then repeat the above action.

Step 3

You repeat about 10-15 times. You should no longer raise your hand above its head, but move it to another position so it can follow. Once the dog has moved to another position, stand up straight and cross your arms across your chest. The dog will notice your hand and automatically sit down and wait for food.

Step 4

As soon as the dog sits down, press the Clicker and give the food immediately. Repeat 10 – 15 times. Then, when the dog puts his butt down, say the command “Sit” and then press the clicker and feed him. Repeat 10 – 20 times. You should review the exercises every day until your dog understands.

6. How to teach a dog to sit left and right

Step 1

You use the Clicker with food in your hand, then coordinate to have the dog move to the right and stand next to your left. Right then, you press Clicker and get rewarded.

Step 2

You repeat the above action several times, then say: “left” (“right”) right after it comes to your left (right).

Step 3

You repeat this action until the dog understands and no longer needs to use the Clicker.

7. Training your dog to ride a motorbike

Teach your dog to maintain balance

First, sit on the saddle and let your dog stand or sit on the saddle right in front of you. Use one hand to hold them tightly to ensure the dog’s safety and that the dog will not fall to the ground. Once your dog gets used to sitting on a motorbike, think about the next training situations.

Teach your dog to voluntarily climb into the car

When you want your dog to sit on the saddle, hit the saddle and give the dog a signal, and at the same time hold the leash and pull them up in the direction of the saddle. You repeat that action many times until the dog becomes familiar and understands your wishes.

Here are 7 ways to train a dog to sit still on the owner’s command that Petlandlover has compiled. Hope you can successfully train your dog!

See more information on: Petlandlover